Influence of photovoltaic generation model and time resolution on the reliability evaluation of distribution systems

This paper aims to investigate the influence of photovoltaic (PV) generation on reliability evaluation of distribution systems. Two PV generation models are used to predict the output power injected into the grid, taking into account the main relevant environmental variables, the irradiance and ambient temperature. Issues that directly affect the output power, such as the spatial smoothing effect due to the plant size and the influence of the irradiance and temperature measurement interval are taken into consideration. Using measurement time series of irradiance and local temperature, the models are used to generate power series in 4‐minute and hourly resolutions. The generated power series are used in a reliability assessment model, with the objective of evaluating the impact of solar resource variability on the reliability indices of the system. Case studies on the IEEE RBTS‐Bus 2 and on the real distribution system of Fernando de Noronha in Brazil are presented and discussed, for power plants of different capacities, considering the effect of the PV generation models, the temporal resolution of the time series and the spatial smoothing of the power output fluctuations. The results show that the power time series in hourly resolution significantly underestimates the frequency of interruptions. For the real system, this index is underestimated at the system level (up to 43%) and at the load points (up to 72%). On the other hand, for the interruption duration index, the temporal aggregation results in a small underestimation (just 4%). The results also indicates that the smoothing effect is irrelevant for typical PV system sizes of distribution systems with discretization equal to or above 4 minutes.     

Effects of ultrasound-assisted resting on the qualities of whole wheat dough sheets and noodles

The effects of resting under ultrasonic treatment on the properties of whole wheat dough sheets and noodles were investigated. Compared with the control group, the resting time to reach the maximum breaking force and extensibility of whole wheat dough sheets treated with ultrasound was shortened by 20 min. The proportion of strongly bound water (T₂₁) decreased, while the proportion of weakly bound water (T₂₂) increased during resting, and the ultrasonic treatment could accelerate this moisture redistribution in the dough. The extent of the increase in gluten macropolymer and the decrease in –SH content of ultrasound-treated wheat dough was higher than that of the control one during the initial 5–15 min resting, which could be related to the improvement of whole wheat dough extensibility. Whole wheat noodles showed a better breaking distance for 10 min of ultrasonic-assisted resting. Ultrasonic treatment could be used to reduce the resting time of whole wheat dough sheets and improve the texture properties of noodles.     

Investigation of the ultimate particle size distribution of a carbonate sand

A series of ring shear tests were conducted to investigate the ultimate particle size distribution of a carbonate sand. The tests were carried out under different stress levels, on three types of specimens: 1) uniformly graded specimens made of dry natural sand 2) remoulded specimens of the crushed sand after first shearing to large strains 3) specimens made of natural sand grains but with the same grading as in (2). The first series of tests on type (1), carried out to very large strains, led to apparently stable gradings, distinct for each stress level. Only limited additional particle breakage could be induced by remoulding the specimens after shearing (type (2)) and subjecting them to more shearing. Tests on specimens created at the apparently stable gradings (type (3)) but from the intact sand particles however led to significantly greater breakage. For the three types a stable, fractal grading was achieved. Analyses of the soil particles’ shape showed that the aspect ratio, sphericity and circularity reach a steady value at large strains, in parallel to reaching a stable grading. The mobilized angle of shearing resistance however was not significantly different in the different types of samples, suggesting the final grading dominates the behaviour.     

The effect of non-uniform temperature on the sorption-enhanced steam methane reforming in a tubular fixed-bed reactor

The effect of non-uniform temperature on the sorption-enhanced steam methane reforming (SE-SMR) in a tubular fixed-bed reactor with a constant wall temperature of 600 °C is investigated numerically by an experimentally verified unsteady two-dimensional model. The reactor uses Ni/Al₂O₃ as the reforming catalyst and CaO as the sorbent. The reaction of SMR is enhanced by removing the CO₂ through the reaction of CaO + CO₂ → CaCO₃ based on the Le Chatelier's principle. A non-uniform temperature distribution instead of a uniform temperature in the reactor appears due to the rapid endothermic reaction of SMR followed by an exothermic reaction of CO₂ sorption. For a small weight hourly space velocity (WHSV) of 0.67 h^?1 before the CO₂ breakthrough, both a low and a high temperature regions exist simultaneously in the catalyst/sorbent bed, and their sizes are enlarged and the temperature distribution is more non-uniform for a larger tube diameter (D). Both the CH₄ conversion and the H₂ molar fraction are slightly increased with the increase of D. Based on the parameters adopted in this work, the CH₄ conversion, the H₂ and CO molar fractions at D = 60 mm are 84.6%, 94.4%, and 0.63%, respectively. After CO₂ breakthrough, the reaction of SMR dominates, and the reactor performance is remarkably reduced due to low reactor temperature.For a higher value of WHSV (4.03 h^?1) before CO₂ breakthrough, both the reaction times for SMR and CO₂ sorption become much shorter. The size of low temperature region becomes larger, and the high temperature region inside the catalyst/sorbent bed doesn't exist for D ≥ 30 mm. The maximum temperature difference inside the catalyst/sorbent bed is greater than 67 °C. Both the CH₄ conversion and H₂ molar fraction are slightly decreased with the increase of D. However, this phenomenon is qualitatively opposite to that for small WHSV of 0.67 h^?1. The CH₄ conversion and H₂ molar fraction at D = 60 mm are 52.6% and 78.7%, respectively, which are much lower than those for WHSV = 0.67 h^?1.     

Evaluation of particle recovery from microalgae

Coccoliths are micro-structured biomineral particles found in cell protective covering layers of coccolithophore species. They are mainly composed of CaCO₃ and their individual crystal entities are arranged in such a way that they construct complex and unique structures. This complexity is found down to the individual particle level and appears to have promising properties to offer. This study focuses on the essential step prior to any kind of implementation, which is the recovery of the material. It summarizes cleaning protocols found in literature, compares them for the first time for the same freshly cultivated material and addresses challenges that still need to be overcome. Further, it highlight the advantages and disadvantages of the best cleaning protocols, suggests optimizations with promising results and uses size distribution measurements to analyse the recovery efficiency. To that end, further characterization techniques, new for coccoliths, are introduced and used to improve our current knowledge of the particles behaviour.     

加工精度对方便米饭理化性质的影响

过度"精、细、白"的大米加工方式造成大量的粮食和营养浪费。为促进我国粮食适度加工政策的实施,研究大米加工精度(DOM)对方便米饭复水性质(水分含量和水分分布)、形态特征(长宽比、延长率和体积膨胀率)、颜色(L值、b值和ΔE值)、质构(硬度和黏度)和微观结构的影响及规律。结果表明,当DOM≥3%时,方便米饭的水分吸收速率、水分分布和形态特征与精白米方便米饭(DOM 12%)相近。当DOM升至6%时,方便米饭的形态特征、总体颜色ΔE值、硬度和微观结构也与精白米方便米饭相近。当DOM达到9%时,方便米饭的黏度已与精白米方便米饭无显著差异。由此可见,生产方便米饭的大米DOM范围宜为6%～9%。用此DOM范围的大米生产方便米饭,可以保留部分糠层营养物质,节约3%～6%的粮食。     

Segregation of dockage and foreign materials in wheat during loading into a 10-m diameter corrugated steel bin

Segregation of dockage and foreign materials (DFM) is an unavoidable phenomenon in bulk grain and causes many problems. In this study, distributions of DFM, and shrunken and broken kernels (SBK) were determined during loading of wheat in a 10-m diameter flat-bottom cylindrical bin. Wheat was loaded through a vertical funnel (spout) into the bin from five drop heights (1.6, 2.5, 3.4, 4.3 and 5.2 m). Samples were collected using a sampling tube (29 cm diameter and 50 cm deep) inserted vertically at five locations (0.00, 1.25, 2.50, 3.75 and 5.00 m of horizontal distances from the center) along three radii of the bin for each drop height. The impurities from each collected sample were divided into five categories with different sizes (other grains, other particles, SBK, fine particles, and dust and fragments) by sieving analyses. Impurities larger and smaller than wheat kernels were categorized as large and small impurities, respectively. Drop height significantly influenced the radial distribution of fine particles, dust and fragments, but not the distribution of other grains and other particles. Fine particles and dust and fragments mainly accumulated in the center, while SBK accumulated mostly near the wall of the bin. Both true density and apparent test weight (bulk density) of unclean wheat and test weight of clean wheat significantly changed along the radius of bin. Apparent test weight of unclean wheat was minimum in the center and close to the wall of bin. Drop height did not influence true density and apparent test weight of clean and unclean wheat. Thousand kernel weight, dimensions, and sphericity of wheat kernels were similar at different radial locations of bin for all drop heights. This study can be used as a reference for further studies on grain handling and associated effects on grain grading system and design of aeration, drying, and insect control. .     

Recent progress of the gas diffusion layer in proton exchange membrane fuel cells: Material and structure designs of microporous layer

Proton exchange membrane fuel cells (PEMFCs) have become the most attractive power supply units for stationary and mobile applications. The operation, design characteristics, as well as performance of PEMFCs, are closely related to the multiphase transport of mass, heat, and electricity in the cell, a critical of which is the gas diffusion layer (GDL). It is very important to guarantee the transmission of water and gasses under high current density, and which is the weakness of PEMFCs at present. Microporous layer (MPL) is considered to be the key variable for mass transfer, so varieties of works focus on modification of MPL materials and its structure design. However, there is still a lack of special review to summarize and prospect the progress of MPL in recent years. This review article therefore focuses on the insights and comprehensive understanding of four critical issues of the MPL, the porosity, pore size distribution, wettability, structural design and the durability of MPL. At last, the conclusion and recommendations section summarized the future prospects and recommendations for possible research opportunities.     

Effect of water distribution in gas diffusion layer on proton exchange membrane fuel cell performance

Water management of proton exchange membrane fuel cells remains a prominent issue in research concerning fuel cells. In this study, the gas diffusion layer (GDL) of a fuel cell is partially treated with a hydrophobic agent, and the effect of GDL hydrophobicity on the water distribution in the fuel cell is examined. First, the effect of the position of the cathode GDL hydrophobic area relative to the channel on the fuel cell performance is investigated. Then, the water distribution in the fuel cell cathode GDL is observed using X-ray imaging. The experimental results indicate that when the hybrid GDL's hydrophobic area lies on the channel, water tends to accumulate under the rib, and the water content in the channel is low; this improves the fuel cell performance. When the hydrophobic area is under the rib, the water distribution is more uniform, but the performance deteriorates.